Introduction

Follow this guide to service and replace the Express 280 components.

Before You Begin

RISK OF SHOCK. Some stations share DC power (“paired” configuration). Pairing should be marked on the AC disconnect or breaker panel. Before performing this procedure, check for pairing and, if present, disconnect the power to BOTH stations at the service panel.

Whether Standalone or Paired, follow standard practice and local code to de-energize the applicable circuit and lock out/tag out the disconnect before proceeding.

Use a multimeter to test that power is off. Keep power off for this circuit until all cover panels are correctly reinstalled and the work scope is completed. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR LOSS OF LIFE.

Do not install or service the charging station in inclement weather. If you work in snow, rain, or wind, you must use a weather-proof shelter that covers all boxes and components.
Keep components in original packaging, free of moisture, and protected from damage until you install or service them at the site. Store all shipments of components in a dry covered location and protect from moisture.
Comply with these guidelines to prevent component damage.
  • Use tools suitable to torque metric fasteners. All fasteners used are in metric sizes.
  • Use the given torque values to tighten the fasteners.
  • Ensure that the tools such as torque tool, multimeter, and Ethernet tester are calibrated.
  • If the charging station is not installed, commissioned, or serviced by a ChargePoint Certified Technician using a ChargePoint-approved method, it is excluded from all ChargePoint and other warranties and ChargePoint is not responsible.
  • You must be a licensed electrician and complete the training at https://www.chargepoint.com/partners/training-certification to become ChargePoint certified and to access the ChargePoint web or app-based installer tools.
When you service a charging station, ChargePoint recommends taking a photo before removing each part, so you can refer to the photo when reassembling.

When removing a part, avoid damage to part by setting it gently on a padded surface.

Follow Service Guide instructions only. Use only ChargePoint-authorized parts.
ChargePoint charging stations are available in various product lines and configurations. Images in this document might not match your station exactly; however, the information is applicable unless otherwise noted.

Additional Documentation

To ensure safety for you and others, do this before you begin:

  • Familiarize yourself with the instructions in the Service Guide.

  • If you have not installed or serviced the Express 280 recently, orient yourself to the Express 280 by reviewing the Site Design, Installation, and Datasheet, as well as any other materials you find helpful.

Access ChargePoint documents at ChargePoint Product Reference Documentation.

ChargePoint Product Documents

Document

Content

Primary Audiences

Datasheet

Full station specifications

Site designer, installer, and station owner

Site Design Guide

Civil, mechanical, and electrical guidelines to scope and construct the site

Site designer or engineer of record

Concrete Mounting Template Guide

Instructions to embed the charging station template in a concrete pad with anchor bolts and conduit placement (these may also be included in the Site Design Guide)

Site construction contractor

Surface Conduit Entry Kit Guide

Instructions for sites where conduit cannot be run underground

Installer

Construction Signoff Form

Checklists used by contractors to ensure the site is correctly completed and ready for product installation

Site construction contractor

Installation Guide

Anchoring, wiring, and powering on

Installer

Operation and Maintenance Guide

Operation and preventive maintenance information

Station owner, facility manager, and technician

Service Guide

Component replacement procedures, including optional components

Service technician

Declaration of Conformity

Statement of conformity with directives

Purchasers and public

Check and Protect Parts

To ensure your safety, do the following:

  • Use only authorized parts and accessories sold and supplied by ChargePoint for the unit and model.

  • Keep components in original packaging, free of moisture, and protected from damage until you install or service them at the site.

  • Store all shipments of components in a dry covered location and protect from moisture.

  • Familiarize yourself with the contents of each shipping box.

  • Ensure that you have all the parts for the work you plan to perform.

  • Have more than one technician or qualified support person present if components are heavy.

  • Keep liquids and objects containing liquid away from the unit, never on or inside.

Do not discard the part you are replacing. Reuse the packaging from the new part to return all removed parts to ChargePoint.

If Damaged, Do Not Service

Do not perform work or remove any signs or covers from the unit if you find any of the following:

  • The charging station housing shows mechanical damage.

  • The charging cables or connectors are visibly damaged.

  • The station is unstable or moves. 

If you find such damage, turn off the station, advise the site manager to keep the unit(s) off, and contact ChargePoint immediately. Find your region’s technical support number at chargepoint.com/support.