Replace the Front Cover Panel

To replace the front cover panel, complete the following steps:

Required Tools and Materials

  • ChargePoint replacement part #CPE250-FRONT-PANELS-F

  • T25 Security Torx driver

  • Step ladder

  • Headlamp

About Panels

All panels have guide tabs that align with corresponding slots on the product’s frame. When removing a panel, lift the panel upward to release these tabs from their slots.

When installing a panel, align these tabs above their corresponding slots and press the panel downward.

Power Off the Station

Power off at the breaker panel and lock out/tag out before continuing work.

RISK OF SHOCK. Before performing this procedure, disconnect the power to the station at the service panel. Keep power off for this circuit until all cover panels are correctly reinstalled and the work scope is completed. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR LOSS OF LIFE.

Remove the Area Light Bar

  1. Using a T25 Security screwdriver, loosen the two captive screws on the area light bar.

    Technical illustration depicts the procedural step.

  2. Disconnect the power cable that connects the area light bar to the LED display assembly. Remove the area light bar.

    When reinstalling, ensure the gasket on each end of the area light bar is properly seated around the plastic tab.

    Technical illustration depicts the procedural step.

Remove the LED Display

  1. Push the LED display upward to release its guide tabs from their corresponding slots on the Express 250’s frame.

    Technical illustration depicts the procedural step.

  2. When the LED display assembly is released, disconnect the five cables from the back.

    When reinstalling, connect the five cables to their corresponding connectors on the back of the display. Leave the area light bar cable (e) loose.

    Technical illustration depicts the procedural step.

    (a) Communications cable (USBClosed Universal Serial Bus-A)

    (b) Holster light cable

    (c) Area light cable x 2 (interchangeable)

    (d) Power cable (24 V)

    Do not allow the LED display to hang from its cables.

Remove the Top Front Panel

Technical illustration depicts the procedural step.

  1. Using two hands, pull the top panel upward to release its guide tabs from their corresponding slots on the Express 250’s frame.

  2. Place a protective cover, such as a lint-free cloth, over the touchscreen to prevent damage during service.

    3. If you are replacing a charging cable, be sure to visit Replace a Holster for information on replacing the holster BEFORE reinstalling the panels.
    When reinstalling, push the bottom edge inward to position it inside the groove in the middle vent panel and engage the edge of the sign. Carefully push the panel down until it is firmly seated.
    When reinstalling, ensure all five cables at the top of the panel are not captured by the front upper panel, and are easily accessible for reinstalling the LED display.

Remove the Middle Vent Panel

  1. Use a T25 Torx driver to remove the M5 screw and washer attaching each touchscreen ground strap to the frame. Keep the screws and washers for reuse.

  2. Loosen both retention knobs (a), allowing the touchscreen beam (b) to slide up vertically and the touchscreen’s bottom edge to clear the middle vent panel’s slot (c).

  3. With hand pressure, tilt the touchscreen upward at a 45-degree angle.

  4. Allow the touchscreen to return to its lowest position vertically. Rotate the retention knobs clockwise to re-tighten.

    The bottom edge and corners of the touchscreen are sharp. Take care when moving underneath the raised screen.

  1. Disconnect the two proximity sensor wires from the connectors on the bottom of the touchscreen and the wire management ring. Move the proximity wires to hang in front of the middle vent panel.

    When reinstalling, connect the proximity sensor wires to their corresponding connectors: left wire to left port and right wire to right port. Route any excess wiring through the right-side wire management ring under the touchscreen, to prevent it being pinched in the panels.

  2. Using two hands, remove the panel by firmly pulling it upward to release the guide tabs from the corresponding slots on the product frame.

    When reinstalling, route both proximity wires under the sheet metal edge, to hang in front of the panel on the right side (as you face the front of the charging station).

    The fins on the back surface of the middle vent panel are sharp. Take care when handling the panel.

Remove the Bottom Front Panel

Remove the bottom front panel by lifting upward from the bottom of the panel to release the guide tabs from their corresponding slots on the Express 250’s frame.

When reinstalling, ensure the panel installation does not tear or break the gaskets on the inner edges of the side extrusions.

REVERSE THE ABOVE STEPS TO REPLACE THE BOTTOM FRONT PANEL, MIDDLE VENT PANEL, TOP FRONT PANEL, LED DISPLAY, AND AREA LIGHT BAR.

Power On the Station

Once all cover panels are installed, power on the station. The on-screen Installation Wizard steps you through any required tasks to set up the station and verify that it can operate properly.

An Installation Wizard test checks that all cover panels are correctly installed and fully seated. Check the lower right corner of the screen for any error messages. If panel errors appear, match the panel letters to this illustration.

Labeled diagram of product, tools or parts.

(a) Front bottom panel

(b) Middle vent panel

(c) Front top panel

(d) LED display

(e) Area light bar

(f) Rear bottom panel

(g) Rear middle panel

(h) Rear top panel

(i) Left extrusion

(j) Right extrusion

RISK OF SHOCK. If a fault exists, turn the power off at the service panel to BOTH product paired charging stations during work and keep it off until all panels are reinstalled. Internal components can present a shock hazard. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR LOSS OF LIFE.

If any panel needs re-installation, review the procedures above to double-check that all panels are fully seated and that the edges of all signs are captured fully by the panels around them. For further details, refer to Introduction.